info@logicaecontrollo.com

+39 0141 769085

  • errore e0 condizionatore

    Commenti disabilitati su errore e0 condizionatore Non categorizzato

    Fault H6 (not always showing fault) Motor is not installed properly and tightly. | View our. In the meantime, use the Aux Button to operate the system. Malfunction Name: Limit/decrease frequency due to antifreezing, Possible Causes: Poor air-return in indoor unit or fan speed is too low. Malfunction Name: The four-way valve is abnormal, A/C Status: If this malfunction occurs during heating operation, the complete unit will stop operation, Malfunction Name: Zero- crossing malfunction of outdoor unit. Le dimensioni minime della stanza vengono indicate sulla targhetta o nella tabella seguente. If outdoor unit detects the condensercoil temperature sensor open circuit or shortcircuit for 5-secsuccessively,condensercoil temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. If indoor unit detects the evaporatorcoil temperature is higher than protective temp. Navigando in internet ci sono varie rtisposte di altri utenti. In thiscase, the unit can automatically resume operation after stopping. During heating operation, the complete unit stops, Malfunction Name: High discharge temperature protection of compressor, A/C Status: During cooling and drying operation, compressor and outdoor fan stop while indoor fan operates. Malfunction Name: Communication Malfunction, A/C Status: During cooling operation, compressor stops while indoor fan motor operates. What is it mean? Possible Causes: There’s no jumper cap on the controller. I have split unit 12 btu its running properly onheat mode but when defrost h1 and start again he stays on heat mode but with cold air ♦ L'installazione del condizionatore d’aria deve essere conforme alle leggi e ai regolamenti nazionali e locali. If the protection occurs over 6 times, the unit will not recover automatically. Indoor Coil Freeze Protection. Thermistor/Bad Connection, or Indoor Air Sensor Failure, Indoor Coil Temp. The fault code is deduced from the number of times the green, © 2014-2020 ACErrorCode.com. A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. Gree Livo Split Air Conditioner Manual PDF, Gree AC Installation and Service Manual PDF, Gree Ductless Inverter Heat Pump Air Conditioner Manual PDF, Gree Multi VRF Air Conditioner Manual PDF, Gree Cassette Type Air Conditioner Error Codes, What is the remedy of error code p6. If outdoor unit detects the high pressure switch iscut off for 3-sec successively, high pressure protection will occur.All the loads (except the 4-way valve in heating mode) will be switched off. Necessary cookies are absolutely essential for the website to function properly. Wait until outside temperature drops to under 95˚F (35˚C). Regards, When start gree invertor when compressor start show PL error. Switch off the unit or re-energize the unit to eliminate this malfunction. Cause: The system has a built-in three-minute delay to prevent short and/or rapid cycling of the compressor. Cause: It is normal for the system to develop condensation or moisture on the discharge air louvers when cooling warm humid air for a long period of time. Jumper cap is damaged. The main board and display panel are not connected well. Between one flash cycle and the next one, a pause of 5 seconds elapses. Malfunction Name: Malfunction protection of jumper cap, A/C Status: Operation of remote controller or control panel is available, but the unit won’t act. Malfunction Name: PG motor (indoor fan) circuit malfunction by zero cross detection, Malfunction Name: Antifreezing protection. If the malfunction occurs 6 times within one hour, the unit will not recover automatically. Possible Causes: Refer to the malfunction analysis (IPM protection, loss of synchronism protection and overcurrent protection of phase current for compressor. Please contact the service center. Malfunction Name: Malfunction of voltage dropping for DC bus-bar, Possible Causes: Supply voltage is unstable, Malfunction Name: Voltage of DC bus-bar is too low, Malfunction Name: Limit/decrease frequency due to high temperature of module. If the malfunction occurs 3 times, the unit will not recover automatically. Solution: The fog or water vapor will disappear as the system cools and dehumidifies the room space. Switch unit off and then switch it on to eliminate this malfunction. A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. All rights reserved. <> ROMA TAXI e NCC. ��x���T�cH�mnY����[a�#z�ܰf�̶����^<4ZJĶ\w�\P���������֣��$��4����wc�m���]D����,i�:_8��~�v���e��r����;Lj��+��=l.=#�6��8�wS�E��W��ӛ��}��$��$�F� S�=)��JJ�b. If outdoor unit detects the compressor discharge temperature sensor is open circuit or shortcircuit for 5-secsuccessively after the compressor has been operating for 3-min, outdoor discharge temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. I have a problem with my gree ac, few minutes after turning on it displays error F2. H6: Indoor fan block:Check if terminal of the indoor motor is connected properly. The appliance should not be used by children without supervision. Il futuro ha una nuova dimensione: vivilo con il nuovo Galaxy S20! Skip to content. Otherwise,contact a qualified service professional for assistance, If problem persists, contact a qualified service professional for assistance. Malfunction Name: Overcurrent protection of phase current for compressor, A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop operation. This website uses cookies to improve your experience while you navigate through the website. Could it be the indoor card ? If there is communication abnormality between display board and indoor unit,communication malfunction will be reported. x��Yˎ\���W�rdD7$��m� @� q, #�A[���H��5����|FΩ�%9}G2i1�j���S����6Ύ����������?�~:��P�9g���c�6礹���kI[�/�����?�N�3ʭ����� �������o �wg�,-�߼;y�������-o�:|u���ϯ^C�\s�7���9��ͯ��9�����I>/���#�p�з����r��q9�=��r�xY�{5�?/{>γ���s�̵�g;>̫?Ώ�?/2>/W����}Kh���i9֯�iH���S۫P�VE���/'�(�������oo�������v�������i��bᇷ����-�?�?��~].Y_̻r����xt�Rj���f]~^������r^v��J^���87?��99�w�~I��w|�޻���o��x}�A��C'3�$�����w����;��q����3�.A�z����+ʆ^�%�xL�5 -���ϔ���k�t��ˆE��=��H?�c���g�~9k��o�/�t캰�����/U�+��g���h�+6K"w\G�UD�,���/�iJ�Z-{.6 If outdoor unit does not receive feedback signal from outdoor fan motor for 30-secsuccessively when the fan motor is operating, an outdoor fan motor malfunction will be reported. Water leaking from the indoor unit into the room. If outdoor unit detects the outdoor ambient temperature sensor open circuit or shortcircuit for 5-secsuccessively, outdoor ambient temperature sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. If problem persists,contact a qualified service professional for assistance. %�쏢 Cause: There are a number of system functions that will prevent air flow. What L3 means i read it in manual it says dc motor malfunction, The code on the unit is A2…. Please can help me any body for this. If it’s no use, please replace control panel AP1. I don’t find any solusion in the maual of use. sensor malfunction will be reported.The unitcan automatically resume operation after the malfunction disappears. Switch off the unit or re-energize the unit to eliminate this protection. errore e1 condizionatore de longhi. Incorrect repairs may cause fire. Cause: There are a number of situations that will prevent the system from running. Decodifica dei codici di errore di tipo E. E0 indica una violazione della funzione di scarico della condensa. ��KK��2μ����^^�"�X�Ԇ�=F�R9���F��徕|��C��^;m�"~3b�- �0������%�����c�(�'��)=^��c�_��Z ����%�ֻ Turn unit off, pull out power plug. If outdoor ambient temperature sensor malfunction occurs in fan mode, only the errorcode is displayed and the indoor unit will operate normally. I found E 7 problems. Cause: While it is normal for the system to generate condensate water in coolingmode, it is designed to drain this water via a condensate drain system to a safe location. Visualizza e scarica il pdf, trova le risposte alle domande più frequenti e leggi il feedback degli utenti. In dry mode, the indoor fan may stop for up to three minutes during the compressor off delay. Thermistor/Bad Connection, or Outdoor Coil Sensor Failure, Compressor Discharge Temp. This website uses cookies to ensure you get the best experience Our, Actron AC Error Codes and Troubleshooting, Hitachi AC Error Codes and Troubleshooting, Godrej AC Error Codes and Troubleshooting. Codici errore Condizionatore Mitsubishi Electric più frequenti con la risoluzione al problema. A/C Status: Indoor fan, outdoor fan, compressor and electric heat tube stop operation. A/C Status: Defrosting will occur in heating mode. Cause: There are a number of possible reasons. Water leaking from the indoor unit into the room. 2. Hello i have dc inverter 1.5 ton when power on ofter 30 mint trip Ac indoor and out door is power off. Gree Air Conditioner Troubleshooting *Problem. General 2ton indoor unit green light red light blinking what problem. Wireless remote controller does not work. Thermistor/Bad Connection, or Outdoor Ambient Sensor Failure, Outdoor Coil Temp. Possible Causes: Discharging after the complete unit is de-energized for 20mins, check whether the thermal grease on IPM Module of outdoor control panel AP1 is sufficient and whether the radiator is inserted tightly. What is it? Possible Causes: Outdoor temperature sensor hasn’t been connected well or is damaged. Possible Causes: After the complete unit is de-energized for 20mins, check whether the thermal grease on IPM Module of outdoor control panel AP1 is sufficient and whether the radiator is inserted tightly. Se si dispone di un modello Midea AC per interni o esterni, gli elenchi dei codici di errore e le definizioni dei guasti sono riportati di seguito. These cookies do not store any personal information. Ifcondenser temperature sensor malfunction occurs in fan mode, only the error code is displayed and the indoor unit will operate normally. System is normal but the indoor tube temperature sensor is abnormal, or the tube temperature sensor is not connected well. High pressure switch is damaged or poorly contacted. Sensor Malfunction. Cambia la forma del domani con il nuovo Galaxy Z Flip. The unit will not run until evaporator temperature is higher than the protective temp. Indoor Configuration Jumper/Missing Configuration Jumper on Indoor Control Board, Indoor/Outdoor Mismatch/Indoor and Outdoor Units Do Not Match, High Current Protection/Power Supply is not Stable and Voltage Range is too Large, Communication Error/Mis-wired or Communication Failure, Indoor Air Temp. Measure the voltage of position L and N on wiring board (XT), if the voltage is higher than 265VAC, turn on the unit after the supply voltage is increased to the normal range. Sir plz tell me how to fix u1 error gree Invertar 1.5 ton. Check if the unit is within hightemperature, high-humidity environment. value and the compressor is stopped for 3-min. If outside temperature or humidity is too high, turn off unit. The unit will restart operation after evaporator temperature is lower than the protective temp. If indoor unit detects the indoor ambient temperature sensor is open circuit or shortcircuit for 5-secsuccessively, indoor ambient temp. Jumper cap is not inserted properly and tightly. Pour out the water inside chassis. What can i do for this error. Cause: While it is normal for the system to generate condensate water in cooling mode, it is designed to drain this water via a condensate drain system to a safe location. Cosa significa l'errore E4 16 sul display del condizionatore? Check if the evaporator and condenser are blocked. Kindly give me an help. The wiring terminal between indoor evaporator temperature sensor and controller is loosened or poorly contacted; There’s short circuit due to the trip-over of the parts on controller; Indoor evaporator temperature sensor is damaged. Possible Causes: There’s circuit malfunction on outdoor unit’s control panel AP1, please replace the outdoor unit’s control panel AP1. Measure the voltage of position L and N on wiring board (XT), if the voltage is higher than 150VAC, turn on the unit after the supply voltage is increased to the normal range. value, the unit will report overload protection. During heating operation, all loads stop. The wiring terminal between outdoor ambient temperature sensor and controller is loosened or poorly contacted; Outdoor ambient temperature sensor is damaged. Indoor Evaporator Coil Temperature Sensor Malfunction. Controller is damaged. Please check it by referring to the resistance table for temperature sensor), 2.The head of temperature sensor hasn’t been inserted into the copper tube, Malfunction of electric expansion valve (EKV). Problem: Outdoor tube temperature sensor is open/short-circuited. The control terminal of PG motor is not connected tightly. Compressor Overload Protection. Batteries in the remote controller are low. Hello th error code of air conditioner GREE KFR-35GW “–” error code. If evaporator temperature sensor malfunction occurs in fan mode, only the error code is displayed and the indoor unit will operate normally. I have gree 12 btu he work properly on heat mode but after h1 defrost I loose the hot air whats the problem? Fan blade rotates roughly due to improper installation. Condizionatore d'aria Midea che mostra un codice di errore? Poor heat exchange (including filth blockage of heat exchanger and bad radiating environment ); Ambient temperature is too high. In heat mode, if the outdoor temperature is low and humidity is high, the system may need to defrost for up to 10 minutes before beginning a heating cycle. Reversing or 4-wayValve Malfunction. Thanks. A/C Status: During cooling and drying operation, the compressor will stop while indoor fan will operate; During heating operating, the complete unit will stop operation. what is the meaning and what is the solution for that, my ac off after 4 to 5 sec compressor off once I saw h6 eror gree ac invertor 1 ton, Error code oE If the indoor unit does not receive signal from indoor fan motor for 30-secsuccessively when the fan motor is operating, indoor fan motor malfunction will be reported. A/C Status: The unit will stop operation as it reaches the temperature point. Outdoor Fan Motor Malfunction. Solution: If water is leaking into the room, it may indicate one of the following What does this indicate ? F1: Malfunction of indoor ambient temperature sensor:Check if indoor room temperature sensor is connected properly. The indoor unit is not level right to left. But opting out of some of these cookies may affect your browsing experience. Possible Causes: Please refer to the malfunction analysis (discharge protection, overload). If the malfunction occurs 6 times within one hour, the unitcannot be recovered automatically. Diciotto pagine di spiegazioni e suggerimenti, per conoscere fino in fondo il tuo nuovo climatizzatore Daitsu, Il Climafacile. Switch off the unit or re-energize the unit to eliminate this protection. These cookies will be stored in your browser only with your consent. Once a failure occurs with the indoor unit in operation, the green unit LED flashes at intervals of 0.5 seconds. Indoor Motor running correct. In case of malfunction (such as bad smell), turn off the power immediately and contact the  service center. The LPP terminal on the main board is not connected well, with the high pressure switch on the complete unit. Moisture orcondensation on the discharge air louvers or outlet vents. If remote controller needs to be replaced,contact a qualified service professional for assistance. Solution: Wash indoor air filter in warm water with mild cleaner. I have carrier cyclojet 1.5 ac when start ac in display show CL for one minute. It is mandatory to procure user consent prior to running these cookies on your website. In some cases, problems can be solved easily without the help from the Customer Service department just by checking the following. F2: Malfunction of evaporator temperature sensor:Check if the evaporator temperature is connected properly. %PDF-1.4 value and the compressor is stopped for 3-minutes. During heating operation, the complete unit stops, Possible Causes: Refer to the malfunction analysis (overload, high temperature resistant), Malfunction Name: Outdoor condenser temperature sensor is open/short circuited. Whats the problem? The remote controller must be within 25 ft. (7.5 m) with no obstructions of the indoor unit. Malfunction Name: Static dedusting protection, Malfunction Name: Overload protection for compressor, Possible Causes: Refer to the malfunction analysis, Malfunction Name: Desynchronizing of compressor, Malfunction Name: Decrease frequency due to high temperature resistant during heating operation, Malfunction Name: Malfunction of phase current detection circuit for compressor, A/C Status: During cooling and drying operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop, Possible Causes: Replace outdoor control panel AP1, Malfunction Name: Charging malfunction of capacitor, Possible Causes: Refer to the part three—charging malfunction analysis of capacitor, Malfunction Name: Malfunction of module temperature sensor circuit, Malfunction Name: Module high temperature protection, A/C Status: During cooling operation, compressor will stop while indoor fan will operate; During heating operation, the complete unit will stop. Indoor Condenser Coil Temperature Sensor Malfunction. Vuoi scoprire le ultime tecnologie, eventi, apps e servizi del mondo Samsung? Refer to the malfunction analysis ( discharge protection, overload). I have a 1200 square foot gree mini split showing a U7 code coming up on the indoor unit. Outdoor Ambient Temperature Sensor Malfunction. High Pressure Protection. I don’t see this code in the manual. how do I repair this? Required fields are marked *. Sul quadro di valutazione dei nuovi condizionatori d'aria appare nei seguenti casi: congelamento dell'evaporatore - si verifica quando la quantità di refrigerante nell'impianto è insufficiente, l'evaporatore e i filtri sono sporchi; If indoor unit detects the evaporator temperature is lower than protective temperate value after the unit has been running for a period of time undercooling or dry mode, the unit will report this fault, in which case the compressor and outdoor fan motor will be stopped. Solution: The noises should discontinue as the refrigerant system equalizes after two or three minute. Supply voltage is too low and load is too high; Outdoor temperature sensor hasn’t been connected well or is damaged. Do not repair the air conditioner by yourself. Cause/Solution. Possible Causes: Refer to the malfunction analysis (IPM protection, loss of synchronism protection and overcurrent protection of phase current for compressor. This category only includes cookies that ensures basic functionalities and security features of the website. If the fault occurs successively 3 times, the unit will not recover automatically. For free inverter, i have a problem when i start a split after 3 minutes compressor suddenly power on and off then only fan working in indoor kindly suggest what is tha problem. If the outdoor unit does not receive data from indoor unit, communication malfunction will be reported. Cause: It is normal for the system to make“water flowing”or“gurgling”sounds from refrigerant pressures equalizing when the compressor starts and stops. In normal state, the resistance for this terminal should be less than 1 ohm. Indoor Ambient Temperature Sensor at ReturnAir Inlet Malfunction. My ac gree inverter duck split.error coming after 30 minutes.what problem.ican fix it.please any body help me? Trova il tuo Climatizzatori e consulta il manuale gratuito richiedilo ad altri proprietari di prodotto. Helo Help is want I am have three errors on one unity h5,e6 and e1 what am I to do, I have gree DC inverter the outdoor unit was at the roof it was laid after a cyclone but it was working there is no gass leaking but now outdoor unit is stopped after a minute I have replaced out for PCB but is same before what do I do ? You also have the option to opt-out of these cookies. Condensate Overflow Protection. During heating operation, the complete unit stops, Possible Causes: Refer to the corresponding malfunction analysis, Malfunction Name: High temperature resistant protection, A/C Status: During cooling operation: compressor will stop while indoor fan will operate. If odors persist, contact a qualified service professional to clean the coil surfaces. If it’s no use, please replace control panel AP1. Level indoor unit. Water leaking from the indoor unit into the room. Indoor unit emits unpleasant odor when started. E4: High discharge temperature protection of compressor, E8: High temperature resistant protection, EU: Limit/ decrease frequency due to high temperature of module, Fo: Gathering refrigerant-Nominal cooling mode, F1: Indoor ambient temperature sensor is open/short circuited, F2: Indoor evaporator temperature sensor is open/short circuited, F3: Outdoor ambient temperature sensor is open/short circuited, F4: Outdoor condenser temperature sensor is open/short circuited, F5: Outdoor discharge temperature sensor is open/short circuited, F6: Limit/ decrease frequency due to overload, F8: Decrease frequency due to overcurrent, F9: Decrease frequency due to high air discharge, FH: Limit/ decrease frequency due to antifreezing, P0: Compressor Min frequence in test state, P1: Compressor rated frequence in test state, P2: Compressor maximum frequence in test state, P3: Compressor intermediate frequence in test state, P5: Overcurrent protection of phase current for compressor, P7: Malfunction of module temperature sensor circuit, H0: Decrease frequency due to high temperature resistant during heating operation, H6: Internal motor (fan motor) do not operate, LP: Indoor unit and outdoor unit doesn’t match, U1: Malfunction of phase current detection circuit for compressor, U3: Malfunction of voltage dropping for DC bus-bar, U5: Malfunction of complete units current detection, U9: Zerocrossing malfunction of outdoor unit, Models: GWH09KF-A3DNB1A / GWH12KF-A3DNB1A/ GWH09KF-D3DNB1C/ GWH12KF-D3DNB1C/ GWH18KG-D3DNB1C/ GWH24KG-D3DNB1A, Gree Portable Air Conditioner Error Codes. L'installazione di questo apparecchio deve essere fatta da un centro assistenza tecnico autorizzato. 1. It on for same time then it started blinking what problem. Problem: Malfunction of temperature sensor. If the wired Tether Controller detects open circuit or shortcircuit of its temperature sensor for 5-secsuccessively,wired controller temperature sensor malfunction will be reported. Fujitsu Error and Fault Codes – Airpro can diagnose all Fujitsu Air conditioning fault and error codes. A/C Status: During cooling operation, compressor will stop while indoor fan will operate; during heating, the complete unit will stop operation. Solution: The condensation or moisture will disappear as the system cools and dehumidifies the room space. Lunedì - Sabato: 9.00 - 19.00 Via Filippo Brunelleschi, 66 - Trezzano sul Naviglio (MI) 393 1981451. Cause: While it is normal for the system to generate condensate water in coolingmode, it is designed to drain this water via a condensate drain system to a safe location. What is J9.. what is the meaning and what is the solution for that.. 1. During cooling and drying operation, compressor stops and indoor fan operates; During heating operation, the complete unit stops operation. A/C Status: During cooling and drying operation, compressor stops while indoor fan will operate; During heating operation, the complete unit will stop operation. Overload Protection. If code still appears, please contact Customer Service. If the PCB is to be replaced, please take off the old for the new PCB. Il condizionatore deve essere installato in una stanza che sia più ampia del minimo consentito.

    Favole Per Bambini, Serpente Figlio Di Loki, Codici Sidi Supplenze 2020, La Teoria Del Tutto Cast, Quanto Costa Mantenere Un Pitbull, Negozi Sport Online, Carpe Non Mangiano, Romeo E Giulietta 1968 Streaming, Don Matteo 13 Si Farà, Azione Partito Calenda,